Mechatronics Canada

November 10, 2022


MC Four Sensing Methods to Verify Part Ejection in Metal Forming 1 400x275

When punching, notching, or trimming metal strips, unwanted material must be cleared before the next press downstroke. If scrap or formed parts inadvertently remain, the press must be stopped before its motion reaches the critical angle, the “point-of-no-return” at which further movement risks damage to the press and die. A variety of precise and reliable sensors are available to protect the die. Keep reading to learn four sensing methods to verify part ejection in metal forming.

Monitor Stripper Plate

MC Four Sensing Methods to Verify Part Ejection in Metal Forming 2 400x275

During the press downstroke, spring-loaded stripper plates push down on the fed material, preventing it from being pulled upward as the punch tooling retracts. Monitoring the presence of the plate during the downstroke confirms there is no material remaining in the die. A missing stripper plate means that something is preventing the plate from bottoming out and the controller must stop the press.

A residual slug pulled through a die can cause major tooling damage

MC Four Sensing Methods to Verify Part Ejection in Metal Forming 3 400x275

In order to avoid such errors and machine downtime it is common to install inductive sensors such as the NMB6-F104M in the lower die to detect strippers. Placing a sensor at each corner ensures the die is fully protected, regardless of where an unwanted metal piece is located (here, one or more of the four corners will not bottom-out).


A pulled slug prevents the plate from bottoming-out

Part Detection on Ejection Chute

MC Four Sensing Methods to Verify Part Ejection in Metal Forming 4 400x275

Sometimes verifying that a part has been ejected is enough to make sure the die is clear. Monitoring the passage of a workpiece through a chute or its free fall into a bin with a thru-beam sensor, such as the MD17MV17 is all that is required. The ejected part is detected when it breaks the beam.


Thru-beam photoelectric sensors confirm the workpiece was ejected

Reliable Object Detection with a Wide Detection Area

MC Four Sensing Methods to Verify Part Ejection in Metal Forming 5 400x275

Slot grids sensors such as the RAL150 are also an ideal choice for confirming part ejection. Compared to a single-line thru-beam, they provide a wider detection area, which is helpful when the position and orientation of the ejected parts cannot be accurately controlled. An entire field for object detection and adjustable sensitivity levels enable reliable detection of both very small and larger objects.


Light grids and slot grid sensors provide a wider detection area

Camera Systems Instantly “Map” Dies

MC Four Sensing Methods to Verify Part Ejection in Metal Forming 6 830x445

Camera systems compare the die surface or tooling to a stored master image

The use of camera technology in industrial environments has evolved rapidly in recent years as camera performance has increased while their cost has decreased. Industrial camera systems such as the vision sensor VOS2000-F226R instantly “map” dies and scan them from a longer distance and make the detection of unwanted slugs and scraps possible. If the scan does not match the image the sensor expects, there is an unwanted part in the area.

If the forming tool has been severely damaged, the discrepancy between the dimensions of an original “pristine” tool and the damaged tool could be detected.

Camera-based sensors require sufficient illumination of the target area for optimal performance. The greater the distance between the upper and lower dies, the less shadowing and the easier to illuminate the picture.


For m ore information, click here 

Pepperl Fuchs Logo 300x150




Latest Articles

  • Prev
  AMRs differ among automation vendors, so it’s important to have a good grasp on the ...
  As electronic devices continue to evolve and shrink, so do their circuits and, ...
  You are in need of a higher total power for your system or machine, or want to ensure ...
  In collaboration with certification entity NC3 and industry partners, Festo Didactic ...
  As a full-service control systems integrator, Mississippi-based Automation and ...
  Kollmorgen is all about innovation, constantly investing in collaborations and ...
  The colloquial term daisy chaining has established itself as a description for ...
  When it’s time to consider a new motion control solution for your application, rule ...
  When punching, notching, or trimming metal strips, unwanted material must be cleared ...
  The future belongs to human-robot cooperation. System builder BEC developed such a ...


  • Prev
  The Cable Entry Systems from Panduit offer a safe, organized method to transition ...
  Designed for human-collaborative (HC) interaction, the highly flexible ...
  Since launching their collaboration in 2021, Comau and Rockwell Automation Inc. have ...
  Featuring built-in hardware security, the Cosy+ range allows users to access ...
  In industries where high system availability is key, knowledge about system states ...
  Cognex Corporation introduces a series of Modular Vision Tunnels designed for ...
  AutomationDirect has added new stainless-steel specialty inductive proximity sensors ...
  In this video, Siemens uses an industrial PC to show how they test the reliability of ...
  AutomationDirect has added IDEM Skorpion rotary trapped key systems. These safety ...
  Since the beginning of October, all the agents at the security company SOS Cash & ...

Sponsored Content

30 Minute Live Webinar 2:30 PM ET January 19th, 2023

MC Siemens Sponsored Content 30 Minute Live Webinar January19 2023 300x250



With PC-based automation, you can implement applications and solutions that far exceed the functions of a classic controller. SIMATIC PC-based products offer you a flexible, innovative platform with long-term availability that give you a home field advantage when meeting the challenges of the digital factory for your machines and plants.


Register now

Featured Product: 

MC Omrons New Integrated Controller Capable of Controlling Robots and Entire Automation Systems 1 400x275

Omron has recently introduced its most full-featured machine automation controller to date. Offering control of multiple robots, the choice of 16, 32, or 64 controlled motion axes, and SQL connectivity. It is the ideal control solution for complete robotic cells, high-speed motion systems, material handling and multi-robot systems.

The Robotics Integrated Platform is the next revolutionary step in the SYSMAC ecosystem that seamlessly integrates the full Omron Fixed Robotics product line. Their one controller approach integrates robot control, in addition to sequence and motion control, to a single controller. This enables synchronized control of robots as well as other devices and results in higher performance compared to typical network based configurations. It also enables users to collect information on devices aligned to a common timeline which not only improves overall system response times and accuracy but also greatly aids in troubleshooting activities.


To read more, click here


Mechatronics Canada

Mechatronics Canada‘s editorial informs and engages a targeted audience of manufacturers, distributors, specifiers and end users delivering an editorial mix of the right content for the right audience.

Subscribe Here

538 Elizabeth Street, Midland,Ontario, Canada L4R2A3 +1 705 527 7666
©2022 All rights reserved

Use of this Site constitutes acceptance of our Privacy Policy (effective 1.1.2016)
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Kerrwil